gpio in A Sentence

    1

    First steps with the Gpio.

    0
    2

    Configure the Gpio pin 4 as an output.

    0
    3

    Gpio output TTL high and low.

    0
    4

    External control function Offering 6 external triggering control(Gpio).

    0
    5

    Raspberry PI and Gpio pins.

    0
    6

    Raspberry PI Gpio.

    0
    7

    Raspberry PI and Gpio pins- What they are and practical uses can give them?

    0
    8

    Web application in HTML + PHP + Python to handle a few Leds through the Gpio.

    0
    9

    Make your own router with WRTNode- controlling LEDs via the Gpio port- A pedestrian in the network.

    0
    10

    I understand that it is because the Gpio is activated to 3,3 volts and the relays are 5V.

    0
    11

    Before you start We have installed the Gpio libraries for Python, and the assembled electronic circuit and working.

    0
    12

    When active the Gpio with script, the Red control led is turned on a momoento, but does not stay on.

    0
    13

    Gpio to Pine 64 What gives us the possibility of developing projects in Python and C/C++ based on this platform.

    0
    14

    And you should keep in mind that there are some Gpio pins with specific functions such as SPI buses, I2C.

    0
    15

    This product can be inserted directly on the PI Gpio interface, users do not need the late welding, plug and play.

    0
    16

    Since the devices that we are going to check with 220V, and pins Gpio Raspberry work with a maximum of 3,3V.

    0
    17

    Perform all the steps that explain and I manage the Gpio from terminal with putty, but since web can not activate the python script.

    0
    18

    Because of the size gained by deleting this connector, There is enough space to add 14 new PIN Gpio, thus leading to a total of 40;

    0
    19

    Total offers of 78 Gpio pins, and the following table extracted from the wiki's WRTNode, We can see the pinout of each and every one of them;

    0
    20

    For that, run sudo visudo in the terminal, and will add it pi under the user so that the user www-data You can control the pins Gpio.

    0
    21

    In the latest posts of this series, We saw they are the Gpio pins and to serve, and How to control the power of leds from the terminal;

    0
    22

    For projects oriented to the Internet of things or the Robotics We have two expansion ports Gpio, which consist of 40 the first pins, and 7 the second;

    0
    23

    The subsystem Gpio is to the end and after the part of the system of files/sys of GNU/ Linux, and actually managed by editing the values of each Gpio port-mapped files.

    0
    24

    For set the port Gpio pins We can export them directly through bash as in the following example, but it should be noted that the libraries have been migrated WiringPI v2 and RPi.

    0
    25

    For this practice, I'm going to use the PI's three branches, that is responsible for adapting all the pins Gpio of Raspberry PI of 3.3V to 5V bi-directionally and will allow us to working with the second reserved for the PiCam I2C bus;

    0
    26

    We can control the led indicator by sending a signal from one of the Gpio of Raspberry to pin Yellow, by default this signal will be received by the Gpio 17 But if we want to we can change the position of the jumper and assign other Gpio as input we will connect to the yellow pin.

    0
    27

    Now that we know that they are the pins Gpio and so they serve, in the next installment we will see a light introduction to the Basic electronics to finally mount a circuit as the following diagram, to turn on a diode Led and check that everything is ready and working properly, what I have called Hello World version Gpio.

    0